Products
|
#CBDD2
Split Crossbuck
Double-Dutch Door
Two Panels
4'-0" height x
4'-0" width
Order Now
| #CBDD2
Split Crossbuck Double-Dutch Door
Two Panels 48" Height x 48" Width
Door Fits a Finished Opening of 48-1/2" Width x 97-1/2" Height
Completely Assembled
Lumber Included
Twin Panels of Multiple BC Lumber
Smooth Surface Lumber Interior Panels
Crossbuck fascia ("x" design) On One side Only
Counter Sunk Wood Screws at Door Back
All Lumber Edges Surrounded with Heavy Gauge No Rust Aluminum
Aluminum Channeling Miter Cut and Secured with Wood Screws
All Necessary Fasteners Included with 6" Zinc Plated Tee-Hinges
Receiver Plates & Zinc-Plated Super Latch Included
All Doors Prepared for Hinges & Latches Upon Request prior to shipment
Reverse Fascia Available at No Charge (What is Reverse Fascia?) |
|
#CBDDNS5
Not Split Crossbuck
Double-Dutch Door
Slider
8’-0” height x
4’3-1/2” width
Order Now
| #CBDDNS5
Not Split Crossbuck Double-Dutch Door
One Sliding Door Panel 51-1/2" Width x 96" Height
Door Fits a Finished Opening of 48" Width x 96" Height and Requires a 7-1/2" Header
Completely Assembled
Lumber Included
One Panel of Multiple BC Lumber
Crossbuck Fascia ("x" design) on Exterior Side Only
Counter Sunk Wood Screws at Door Back
All Lumber Edges Surrounded With Heavy Gauge No Rust Aluminum
One Self Cleaning & Aligning Rounded Door Track Included
Two Ball Bearing Adjustable Trolleys Included with Each Door Panel
Two of Armour's Best Aluminum No Rust Door Stops Included
All Necessary Fasteners to Hang Track, Mount Latch & Stops Included
Receiver Plates & Zinc-Plated Super Latch Included
All Doors Prepared for Latches Upon Request
|
|
#CBHD1
Crossbuck Lumber
Half Dutch Gate
4'-0" Height x
4'-0" Width
Order Now
| #CBHD1
Crossbuck Half Dutch Door
One Gate Panel 48" Width x 48" Height
Gate Fits a Finished Opening of 48-1/2" Width x 97-1/2" Height
( A 97-1/2" Height is only recommended when this half door is combined
with an additional Armour Bar Top or Crossbuck Half Dutch Door.)
Completely Assembled Stall Gate with Hardware
Old World Crossbuck "x" Design
Heavy gauge "non-rusting" ALUMINUM metal used throughout entire gate structure (except lumber)
Full vertical & horizontal channel coverage on both sides of door for
maximum strength and protection
6" Zinc Plated Tee-Hinges with all necessary fasteners included for
installation.
Zinc-Plated Superlatch and latching receiver plates and hardware
included with all gates.
Smooth surface inside door panel.
All lumber secured with glue and countersunk wood screws on rear
panels.
All Gates prepared for latching and hinging prior to shipment upon
request at no charge.
Check out the Double-Dutch Door
|
|
#BTHD1
Bar Top
Half Dutch Gate
4'-0" Height x
4'-0" Width
Order Now
| #BTHD1
Bar Top Half Dutch Door
One Panel 48" Width x 48" Height
Door Top Fits a Finished Opening of 48-1/2" Width x 97-1/2" Height
(A 97-1/2" height is recommended when bar top is combined with
any of Armour's standard half Dutch bottoms.)
Full Height 1-3/4" x 1-3/4" x 1/8" Square Tubing Posts.
Completely Assembled
1" Diameter Round Vertical Pickets (Bars)
1/8” Heavy Gauge No Rust Aluminum Throughout
3” Between Picket (Bar) Spacing (1" & 2" available)
Concealed Welds Throughout Bar Top
All Necessary Fasteners Included with 6" Zinc Plated Tee-Hinges
Receiver Plates & Zinc-Plated Super Latch Included
All Bar Tops Prepared for Hinges & Latches Upon Request
Smaller Custom Sizes are Available (Nothing Exceeding 48" Width x 48" Height)
|
|
#TGHD1
6" T&G Lumber
Half Dutch Gate
4'-0" Height x
4'-0" Width
Order Now
| #TGHD1
6" Tongue & Groove Fascia Half Dutch Door
One Half Door Panel 48" Width x 48" Height
Half Door Fits a Finished Opening of 48-1/2" Width x 97-1/2" Height
(A 97-1/2" height is only recommended when this half door is combined
with an additional Armour Bar Top or T&G Half Dutch Door.)
Completely Assembled Stall Gate with Hardware
#1 Southern Yellow Pine 6" Tongue and Groove Design
T&G lumber is available in horizontal or vertical design
Heavy gauge "non-rusting" ALUMINUM metal used throughout entire gate structure (except lumber)
Full vertical & horizontal channel coverage on both sides of door for
maximum strength and protection
6" Zinc Plated Tee-Hinges with all necessary fasteners included for
installation
Zinc-Plated Superlatch and latching receiver plates and hardware
included with all gates
Smooth surface inside door panel
All lumber secured with glue and countersunk wood screws on rear
panels
All Gates prepared for latching and hinging prior to shipment upon
request at no charge.
Check out the Double-Dutch Door
|
|
#TVHD1
Taube Vent
Half Dutch Gate
4'-0" Height x
4'-0" Width
Order Now
| #TVHD1
Taube Half Dutch Door
One Half Door Panel 48" Width x 48" Height
Half Door Fits a Finished Opening of 48-1/2" Width x 97-1/2" Height
(a 97-1/2" height is only recommended when this half door is combined
with an additional Armour Bar Top Door.)
Completely Assembled
Great for Ventilation
1" Diameter Round Vertical Pickets (Bars)
1/8" Heavy Gauge No Rust Aluminum throughout
1" Between Picket (Bar) Spacing
Concealed Welds Throughout Vent Panel Lower Door Grille
Vent Panel Lower Door Grille with Miter Cut Aluminum Corners
Lumber Included
Twin Panels of Multiple BC Lumber
Counter Sunk Wood Screws at Door Back
Lumber Glued & Braded for Additional Strength
All Lumber Edges Surrounded with Heavy Gauge No Rust Aluminum
Aluminum Channeling Miter Cut and Secured with Wood Screws
All Necessary Fasteners Included with 6" Zinc Plated Tee-Hinges
Receiver Plates & Zinc-Plated Super Latch Included
All Doors Prepared for Hinges & Latches Upon Request
|
|
#CBDDNS2
Not Split Crossbuck
Double-Dutch Door
Hinged
8’-0” height x
4’3-1/2” width
Order Now
| #CBDDNS2
Not Split Hinged Crossbuck Double-Dutch Door
One Hinged Door Panel 48" Width x 96" Height
Door Fits a Finished Opening of 48-1/2" Width x 96-1/2" Height
Completely Assembled
Lumber Included
One Panel of Multiple BC Lumber
Smooth Surface Lumber Interior Panels
Crossbuck ("x" design) on One Side Only
Counter Sunk Wood Screws at Door Back
Lumber Glued & Braded for Additional Strength
All Lumber Edges Surrounded with Heavy Gauge No Rust Aluminum
Aluminum Channeling Miter Cut and Secured With Wood Screws
All Necessary Fasteners Included with 6" Zinc Plated Tee-Hinges
Receiver Plates & Zinc-Plated Super Latch Included
All Doors Prepared for Latches Upon Request
Doors Center Receives Two Strategically Placed Center Strips for Cosmetic Split Dutch Appearance
Reverse Fascia Available at No Charge (What is Reverse Fascia?)
|
|
